LED chip manufacturing process and testing project analysis

Jul 04, 2017

Leave a message

Chip is the most critical raw materials LED, its quality is good or bad, directly determines the performance of the LED. Especially for automotive or solid-state lighting equipment, high-end LED, absolutely not allow defects, that is, the reliability of such equipment must be very high. However, the LED packaging plant due to lack of chip incoming inspection experience and equipment, usually not on the chip incoming inspection, in the purchase of substandard chips, often only eat dumb loss. Jin Jian detection in the accumulation of a large number of cases of LED failure analysis on the basis of the introduction of LED chip incoming inspection business, through the use of high-end analytical instruments to identify the advantages and disadvantages of the chip situation. This testing service can be used as LED packaging plant / chip agent factory inspection of the supplement to prevent the defective chip storage, to avoid the chip quality problems caused by the overall loss of the lamp beads.


Test items:


First, the chip performance parameters of the test


Wd (main wavelength), Iv (brightness), Vf (forward voltage), Ir (leakage), ESD (antistatic ability) and other chip photoelectric performance test, Jin Jian as a third party testing organizations to identify suppliers to provide products Whether the data is up to standard.


Second, chip defect search


Test content:


1. Chip size measurement, chip size and electrode size to meet the requirements, the electrode pattern is complete.


2. Chip solder joint contamination, solder joint damage, grain damage, grain cutting size, grain cutting tilt and other defects.


LED chip damage will lead directly to LED failure, so improve the reliability of LED chips is essential. During the deposition process, it is sometimes necessary to fix the chip with a spring clip, thus creating a clip. If the yellow light operation is not complete and the mask has a hole will make the light area has more residual metal. Grain in the previous process, the process such as cleaning, evaporation, yellow, chemical etching, fusion, grinding and other operations must use tweezers and flower baskets, vehicles, etc., so there will be grain electrode scratches occur.


Chip electrode on the solder joint: chip electrode itself is not solid, resulting in wire after the electrode off or damage; chip electrode itself poor solderability, will lead to solder ball solder; chip storage will lead to improper electrode surface oxidation, surface contamination And so on, the slight contamination of the bonding surface may affect the diffusion of metal atoms between the two, resulting in failure or Weld.


3. Chip extension area of the defect search


LED epitaxial wafers in the high temperature process, the substrate, MOCVD reaction chamber residual sediment, peripheral gas and Mo source will introduce impurities, these impurities will penetrate the epitaxial layer, to prevent gallium nitride crystal nucleation, the formation of various A variety of epitaxial defects, and ultimately in the epitaxial layer surface formation of small holes, which will seriously affect the epitaxial wafer film material quality and performance. Jin Jian detection developed a rapid identification of chip epitaxial area defect detection method, low cost, quickly detect the chip epitaxial layer of 80% of the epitaxial defects, to help LED customers choose high-quality epitaxial wafers, chips.


4. Chip technology and cleanliness observation


Electrode processing is the key process for making LED chips, including cleaning, evaporation, yellowing, chemical etching, fusion, grinding, will come into contact with a lot of chemical cleaning agent, if the chip is not clean enough, will make harmful chemical residues. These harmful chemicals will be in the LED power, and electrochemical reaction with the electrode, resulting in dead lights, light failure, dark, black and so on. Therefore, the identification of chip chemical residues on the LED packaging plant is essential.


LED chip manufacturing process flow chart


Epitaxial Film → Cleaning → Plating Transparent Electrode Layer → Transparent Electrode Graphic Photolithography → Corrosion → Deposition → Platform Graphic Lithography → Dry Etching → De-Adhesive → Annealing → SiO2 Deposition → Window Graphic Lithography → SiO2 Corrosion → Glue → N-pole lithography → pre-cleaning → coating → peeling → annealing → P-pole pattern lithography → coating → peeling → grinding → cutting → chip → finished product testing.


After growing into an epitaxial wafer, the next step is to start the electrode (P pole, N pole) of the LED epitaxial wafer, and then start cutting the LED epitaxial wafer with a laser or diamond knife, making it into a chip and then on the wafer 9 points in different locations to do the parameters of the test. This is mainly on the voltage, wavelength, brightness test, in line with the normal shipping standard parameters of the wafer to continue the next step, do not meet the requirements, put on the side of another deal. After the wafer is cut into chips, 100% of the visual inspection (VI / VC) is required, and the operator is visually under a 30-fold magnification microscope. And then use the automatic sorting machine according to the different voltage, wavelength, brightness prediction parameters of the chip fully automated selection, testing and classification. Finally, the LED chip to check (VC) and labeling. The chip type, lot number, quantity and photoelectric measurement statistics are recorded on the label and attached to the back of the wax paper. Blue film on the chip will do the final visual inspection, visual inspection standards and the same as the first to ensure that the chip arrangement and quality of qualified. This is the LED chip manufacturing process.